Merhaba ;
VFD-E serisi sürücünün bağlı olduğu motor
başka bir tahrik sistemi tarafından döndürülmektedir ancak
sürücüye start verdiğimiz zaman frenleme yapıp 0hz başlamak yerine
tahrik sistemi tarafından döndürülen motor o anlık devir frekansına karşılık gelecek hz başlayabilirmi yada
bizim belirleyeceğimiz start frekansı ilede başlayabilirmi
Önemli Bilgilendirme!
Forum sayfamızdan sınırsız faydalanmak için kullanıcı kaydı oluşturup giriş yapmalısınız. Özellikle mesaj eklentileri, linkler kullanıcı girişi yapmazsanız görüntülenmeyecektir. Aşağıdaki linke tıklayarak üye değilseniz kullanıcı oluşturabilirsiniz.
https://destek.delta-turkey.com/ucp.php?mode=register
Forum sayfamızdan sınırsız faydalanmak için kullanıcı kaydı oluşturup giriş yapmalısınız. Özellikle mesaj eklentileri, linkler kullanıcı girişi yapmazsanız görüntülenmeyecektir. Aşağıdaki linke tıklayarak üye değilseniz kullanıcı oluşturabilirsiniz.
https://destek.delta-turkey.com/ucp.php?mode=register
VFD-E SERİSİ
- emre çoban
- Mesajlar: 26
- Kayıt: 23 Mar 2020, 11:30
- İletişim:
- Durum: Çevrimdışı
- TRAKYA_HIDROPAR
- Mesajlar: 15
- Kayıt: 05 Ara 2018, 22:19
- İletişim:
- Durum: Çevrimdışı
Re: VFD-E SERİSİ
Merhaba,
Aşağıdaki parametreye göre enkoder kartı takılırsa olur gibi görünüyor. emin olamadım
08.26 Speed Search during Start-up
Factory Setting: 0
Settings 0 Disable
1 Enable
This parameter is used for starting and stopping a motor with high inertia. A motor with high
inertia will take a long time to stop completely. By setting this parameter, the user does not
need to wait for the motor to come to a complete stop before restarting the AC motor drive. If a
PG card and encoder is used on the drive and motor, then the speed search will start from the
speed that is detected by the encoder and accelerate quickly to the setting frequency.
When using this parameter with PG feedback control, this function will be enabled as Pr.13.00
and Pr.13.01 are set. It has no relation with Pr.00.10. Pr.08-04 and Pr.08-06 will be disabled
when using this parameter with PG feedback control.
Please make sure Pr.13.00 to Pr.13.02 are set correctly. An incorrect setting may cause the
motor to exceed its speed limit and permanent damage to the motor and machine can occur.
Aşağıdaki parametreye göre enkoder kartı takılırsa olur gibi görünüyor. emin olamadım
08.26 Speed Search during Start-up
Factory Setting: 0
Settings 0 Disable
1 Enable
This parameter is used for starting and stopping a motor with high inertia. A motor with high
inertia will take a long time to stop completely. By setting this parameter, the user does not
need to wait for the motor to come to a complete stop before restarting the AC motor drive. If a
PG card and encoder is used on the drive and motor, then the speed search will start from the
speed that is detected by the encoder and accelerate quickly to the setting frequency.
When using this parameter with PG feedback control, this function will be enabled as Pr.13.00
and Pr.13.01 are set. It has no relation with Pr.00.10. Pr.08-04 and Pr.08-06 will be disabled
when using this parameter with PG feedback control.
Please make sure Pr.13.00 to Pr.13.02 are set correctly. An incorrect setting may cause the
motor to exceed its speed limit and permanent damage to the motor and machine can occur.
- Uğur
- Mesaj Panosu Yöneticisi
- Mesajlar: 9521
- Kayıt: 06 Mar 2018, 10:37
- Konum: İstanbul
- İletişim:
- Durum: Çevrimdışı
Re: VFD-E SERİSİ
08-26 08-27 ve 08-28 parametrelerinden ayarlayabilirsiniz enkoder kartı zorunluluğu yoktur. Olması durumda çalışma farklılık gösterir.
Uğur Birdal - Technical Support Team Manager - DELTA Electronics Turkiye
Bildirimler İçin Whatsapp Kanalımıza Katılın
Whatsapp Kanal
https://www.linkedin.com/in/ugurbirdal
Bildirimler İçin Whatsapp Kanalımıza Katılın
Whatsapp Kanal
https://www.linkedin.com/in/ugurbirdal
- TRAKYA_HIDROPAR
- Mesajlar: 15
- Kayıt: 05 Ara 2018, 22:19
- İletişim:
- Durum: Çevrimdışı
Re: VFD-E SERİSİ
Merhaba Uğur Bey,
sahada uygulamacı arkadaşdan gelen bilgiye 8-26 yı 1 yaptıktan sonra çalışırken frekans yakalama güzel her hangi bir sorun yok fakat, motor dururken start verildiğinde ilk önce ters yöne yaklaşık bir tur atıp daha sonra istenen yöne dönmeye başlıyormuş. bu nedenle 8-26 tekrar eski haline getirildi. hız arama fonkisyonun da motor dururken startta bu geri dönme neden kaynaklı olabilir acaba? 8-27 0 ve 1 olarak denendi.
sahada uygulamacı arkadaşdan gelen bilgiye 8-26 yı 1 yaptıktan sonra çalışırken frekans yakalama güzel her hangi bir sorun yok fakat, motor dururken start verildiğinde ilk önce ters yöne yaklaşık bir tur atıp daha sonra istenen yöne dönmeye başlıyormuş. bu nedenle 8-26 tekrar eski haline getirildi. hız arama fonkisyonun da motor dururken startta bu geri dönme neden kaynaklı olabilir acaba? 8-27 0 ve 1 olarak denendi.
- Uğur
- Mesaj Panosu Yöneticisi
- Mesajlar: 9521
- Kayıt: 06 Mar 2018, 10:37
- Konum: İstanbul
- İletişim:
- Durum: Çevrimdışı
Re: VFD-E SERİSİ
Bu durumda hız arama akımını arttırmayı deneyin.
Uğur Birdal - Technical Support Team Manager - DELTA Electronics Turkiye
Bildirimler İçin Whatsapp Kanalımıza Katılın
Whatsapp Kanal
https://www.linkedin.com/in/ugurbirdal
Bildirimler İçin Whatsapp Kanalımıza Katılın
Whatsapp Kanal
https://www.linkedin.com/in/ugurbirdal